MK2 Engines
This article hopes to describe the tuning process used in the LoveHorsepower Fuel Pressure Regulator and Tuning Video guides. The following equipment was installed:
Apex-i S-AFC (Super Air Fuel Controller).
LoveHorsepower Fuel Pressure Regulator Kit (Aeromotive Fuel Pressure Regulator).
Innovate Motorsports LC-1 Wideband Lambda Cable (Wideband Oxygen Sensor Kit).
LoveHorsepower Stage Two Water Injection.
550cc/min Fuel Injectors from the twin [...]
View the original content on Lovehorsepower.com
Well I had a fraying throttle cable that was getting hung up at times when backing off the throttle… After further inspection I noticed that the throttle cable was fraying and was getting caught up not letting the cable slide smoothly to close the throttle plate. Well after a call to “SATAN” I was quoted around 80 bux for about 1.5feet of throttle cable. A bit much if you ask me, and im sure I could do this for cheaper.
View the original content on International MR2 Owners Club
3S-GTE • Engines • MK2 • Tuning
Relavant mods are
* T3/T4 50trim Turbocharger (nocash kit)
* Supra Twin Turbo 540cc/min fuel injectors
* Apexi S-AFC
* Aeromotive adjustable fuel pressure regulator
* Two stage water injection
* Greddy Intercooler
* K&N FIPK Intake
* Apexi AVC-R boost controller
* Ross forged pistons
View the original content on Lovehorsepower.com
5S-FE • Forced Induction • MK2
Modifying your 5S-FE
There are a lot of nay-sayers out there that say the 5S-FE motor is a weak non-performance economy motor and can’t handle the boost. I don’t agree with this assumption and feel that many setups are not so much limited by the motor itself but by their owner’s understanding of how it works. [...]
Tags: 5S-FE, Engines, forced induction, turbocharger
View the original content on International MR2 Owners Club
BEAMS 3S-GE • Engines • MK2
Okay, so this seems to come up every now and then, usually people wanting to know if they can fit an Altezza engine into their MR2.
A few people have fitted FWD engines in a RWD setup, which is easier on some regards, but has it’s own set of problems too.
Okay, so what are the main [...]
Tags: beams, guide, install, rwd, transverse
View the original content on International MR2 Owners Club
Engine: There are too many to count as toyota used them in alot of vehicles
3VZ-FE toysrme?
4VZ-FE JDM?
5VZ-FE Found in 1995.5-2004 Tacomas, 96-02 4runner, 95 T100(Rumor has it this was a Disti 5vz),00-03 Tundra -Weasy2k
1MZ-FE 94-99 Avalon, 94-02 Camry, 99-02 Solara, 98-03 Sienna
1MZ-FE*^ 03-04 Camry/Solara
1MZ-FE* 98-99 es300/rx300, 00-04 avalon/sienna 01-04 highlander
2MZ-FE* JDM?
3MZ-FE*^ 03-05 highlander, 04-05 Sienna, [...]
View the original content on International MR2 Owners Club
BEAMS 3S-GE • Engines • MK2
Well… This seems to come up every now and then.
People complaining that the beams engine is too rare/expensive.
So here’s my guide, on how to go about getting a 200+hp 3SGE, for the least amount of money!
Firstly, the gearbox: Your standard gearbox is more than fine. LSD is fun, but definitely not needed.
Standard hubs/axles/etc are fine [...]
View the original content on International MR2 Owners Club
3S-GTE • Forced Induction • MK2
Welcome to another video installation how-to from LoveHorsepower.com!
LoveHorsepower Fuel Pressure Regulator Kit Installation Video – Full Resolution – 115MB windows media format. Right click and save as to view.
Fuel Pressure Regulator Video Tuning Guide Video – Full Resolution – 92MB windows media format. Right click and save as to view.
Some of the pictures and notes [...]
Tags: install, regulator, turbocharger
View the original content on Lovehorsepower.com
Welcome to the firist video installation how-to from lovehorsepower.com!
Kirkosaurus Motor Mount Installation Video – Full Resolution – 52MB windows media format. Right click and save as to view.
Some pictures from the video, are presented here, but please see the video instead for the how to.
Here is the front motor mount on the MR2 Turbo. Remove [...]
Tags: motor mount
View the original content on Lovehorsepower.com
Here is a quick write up on how to change your distributor cap and rotor. This was done on a 93T with no egr system which may make it a little easier than those of you who still have your egr.
Tags: cap, distributor, rotor
View the original content on International MR2 Owners Club
Disclaimer: This documentation in no way replaces the Toyota MR2 Repair Manuals. The purpose of this content is only to provide supplementary information to fellow MR2 enthusiasts. Midship Runabout and its contributing authors will not be held responsible for any injury or damages that may occur as the result of practicing any of the methods or procedures described within this website.
